• No.95 Qilian street, block B, 22F, High-tech Zone,Shijiazhuang City, China, 050000
  • Follow On Social :
Common Issues and Self-Diagnostic Procedures for High Voltage Circuit Breaker Testers
Common Issues and Self-Diagnostic Procedures for High Voltage Circuit Breaker Testers
1.1 1. Instrument Cannot Power On / Circuit Breaker Trips During Operation 1.1.1 1.1 Instrument Does Not Power On If the instrument fails to power on, first verify that the AC power supply is available. Check the power outlet, power reel, or distribution panel to ensure the input power is functioning properly. If the external power supply is normal, disconne···
2Self-Diagnosis of the Control Power Supply
2Self-Diagnosis of the Control Power Supply
Before troubleshooting the instrument, verify that the Control and DC Power jumper connections on the front panel are correctly installed. During testing, the DC Power Switch must be set to the ON position. When enabled: HandyThe switch indicator remains illuminated. HandyThe DC output indicator remains illuminated. After confirming the above conditions, set···
Circuit Breaker Operates, but No Timing Results Are Displayed
Circuit Breaker Operates, but No Timing Results Are Displayed
3.1 Verify the Timing Contact Channels (Hardware Check) Short-circuit the timing channel A1–N1 using a jumper wire. Observe the timing status indicator on the instrument display. Expected behavior: HandyWhen A1 and N1 are shorted, the indicator should become solid, indicating a closed contact. HandyWhen the jumper is removed, the indicator should become hol···
The Circuit Breaker Operates During Testing, Yet No Time Data Appears In Test Results
The Circuit Breaker Operates During Testing, Yet No Time Data Appears In Test Results
HandyGeneral vacuum circuit breakers require research on bounce parameters, while plug-in metal contact circuit breakers with voltage levels of 35kV and above generally do not study bounce parameters. However, during the experiment, it is necessary to consider the "false bounce" caused by vibration of the wiring clamp or high-altitude wiring clamp during the···
Inaccurate Measurement Of Opening And Closing Time In Opening And Closing Tests/Setting Of Control T
Inaccurate Measurement Of Opening And Closing Time In Opening And Closing Tests/Setting Of Control T
Combination and division test setup The closing and opening control time of the high-voltage switch tester produced by our company refers to the time from the issuance of the closing control pulse to the issuance of the opening control pulse (in the case of reclosing operation, it refers to the time when the second opening control pulse is issued). The defau···
Measurement Of The Coordination Time Between The Main And Auxiliary Contacts
Measurement Of The Coordination Time Between The Main And Auxiliary Contacts
The wiring instrument is equipped with two sets of contact wiring terminals as shown in the figure below. A1, B1, C1, A2, B2, C2, N1 are grouped together (used to test the main contact time). A3, B3, C3, A4, B4, C4, N2 are grouped together and can measure six auxiliary contacts or six main contacts. When A3 to C4 are set as auxiliary contacts, the fitting ti···
The Sensor Is Working Normally, But The Closing/Opening Speed Measurement Is Incorrect/The Speed Is
The Sensor Is Working Normally, But The Closing/Opening Speed Measurement Is Incorrect/The Speed Is
Firstly, the speed test results need to be compared with the factory report. Therefore, the selection of speed sensors needs to be kept "in the same position" and "of the same type" as the factory test of the circuit breaker manufacturer. Sensors installed for different types of movements should not be replaced arbitrarily in principle. Linear motion sensors···
Sensor Types Corresponding To Various Sensors
Sensor Types Corresponding To Various Sensors
Usually, the sensor type options for Handi switch testers include analog linear, digital rotation, digital linear, acceleration, and gyroscope (some older software or basic instruments do not have digital rotation, digital linear, and gyroscope options) Simulated linearity includes: all linear or rotational sensors based on the principle of sliding line rheo···
Self Checking Judgment Of Whether The Sensor Has No Signal Or Is Faulty
Self Checking Judgment Of Whether The Sensor Has No Signal Or Is Faulty
When using the XC355 simulated rotation sensor with blind spots (the effective angle of XC355 is 345 °± 2 °), it should be ensured that the sensor cursor on the test interface is close to the middle grid. Note: The white scale line on the new sensor knob can indicate the cursor position, which can be used for quick installation. If the knob is loose, the ···
The Difference Between “Input Type” And “Measurement Type” Sensors
The Difference Between “Input Type” And “Measurement Type” Sensors
In the vast majority of cases, instruments use input type. (Acceleration and gyroscope sensors can only use input type) Input type refers to the instrument recording the voltage change curve of the sensor as the travel curve. This curve itself does not have the meaning of travel length. We set a travel length specified by the switch factory and calibrate the···
Meaning Of The Symbol For Protective Current Transformers
Meaning Of The Symbol For Protective Current Transformers
Error limit of protective current transformer accuracy level Under rated primary current Current error (±%) Under rated primary current phase difference Composite error under rated accuracy limit of one current % ±(´) ±crad 5P 10P 1 3 60 - 1.8 - 5 10 Example: A current transformer with the symbol 5P20, 30VA, 1000/5 is represented as follows: transfor···
Error Curve Of Current Transformer
Error Curve Of Current Transformer
From the above figure, it can be seen that the primary current IP of the current transformer is divided into two parts after being transformed into the secondary current. A small portion is used for internal loss excitation, magnetic loss, and eddy current loss. The other part flows into the secondary circuit, which is the secondary current IS measured exter···
When There Is Inaccurate Measurement Of The Transformation Ratio
When There Is Inaccurate Measurement Of The Transformation Ratio
1. When there is inaccurate measurement of the transformation ratio, the following measures can be taken: 2. On the premise of ensuring non instrument related issues (such as hardware failures), the following measures can be taken to solve them: 3. 1. Check for poor contact on the test wire and replace it if necessary (sometimes a multimeter alone cannot gua···
If Overcurrent Protection Occurs During Ct Excitation Characteristic Testing,
If Overcurrent Protection Occurs During Ct Excitation Characteristic Testing,
1. If overcurrent protection occurs during CT excitation characteristic testing, the following methods can be tried to solve it: (1) Reduce the boost speed (2) Reduce the maximum test current 2. During CT testing, overheating protection occurs: The instrument has overheat protection function. When the internal temperature reaches 75 degrees, it will cause th···
Can The Transformer Tester Test The Transformation Ratio Of Capacitive Voltage Transformers
Can The Transformer Tester Test The Transformation Ratio Of Capacitive Voltage Transformers
The transformer tester produced by our company can measure electromagnetic transformers and ensure that the measured transformer ratio accuracy meets the technical parameters in the manual. After reducing accuracy requirements, users can also use it for measuring the transformation ratio of capacitive voltage transformers. When testing capacitive voltage tra···
Solution for Transformer Tester Unable to Generate Reports
Solution for Transformer Tester Unable to Generate Reports
Solution for Transformer Tester Unable to Generate Reports: At present, the supporting software supports calling Microsoft Office software to generate reports. Please check if Microsoft Word is installed on your PC before generating the report. Our company is continuously improving the software testing report generation function and will support more office ···
How To Check If The Transformer Tester Is Working Properly?
How To Check If The Transformer Tester Is Working Properly?
Short circuit S1 of the instrument's "voltage output", S1 of "voltage measurement 1", and P1 of "voltage measurement 2"; Short circuit S2 for "voltage output", S2 for "voltage measurement 1", and P2 for "voltage measurement 2". Connect the multimeter to the "voltage output" and select the AC voltage gear. Enter System Settings ->Calibration, press the number···
P-Level Current Transformers Can Determine Whether The Accurate Limit Factor Kalf Is Qualified By Me
P-Level Current Transformers Can Determine Whether The Accurate Limit Factor Kalf Is Qualified By Me
P-level current transformers can determine whether the accurate limit factor KALF is qualified by measuring the excitation curve. The method is as follows: 1、 Measure the DC resistance RCT of the secondary winding and calculate the impedance ZCT=RCT+jXCT of the secondary winding. XCT can be ignored or taken as 0.1~0.2 Ω. 2、 Calculate the rated load impeda···
How To Check If The Instrument Is Working Properly?
How To Check If The Instrument Is Working Properly?
Q: How to check if the instrument is working properly? Answer: Short circuit the power outputs A, B, and C with the voltage measurement UA, UB, and UC respectively. Select the positive sequence capacitor in the test options and start the test. If the three-phase voltage output is consistent with the set voltage, it indicates that the instrument is normal.
What Aspects Should Be Paid Attention To When Testing The Mutual Inductance Of Line Parameters?
What Aspects Should Be Paid Attention To When Testing The Mutual Inductance Of Line Parameters?
Q: What aspects should be paid attention to when testing the mutual inductance of line parameters? Answer: 1、 Before testing the mutual inductance, the induced voltage of the circuit should be measured to not exceed 750VAC. 2、 There are two methods to measure mutual inductance with the instrument (note that the wiring and frequency selection should be cons···
What Aspects Should Be Paid Attention To When Testing The Wiring Of Line Parameters?
What Aspects Should Be Paid Attention To When Testing The Wiring Of Line Parameters?
Q: What aspects should be paid attention to when testing the wiring of line parameters? Answer: 1. The protective grounding column on the instrument panel and the N terminal of the test power output must be reliably grounded, and the tested circuit must be reliably grounded through a grounding knife switch during the wiring or disconnection process. 2. The c···
How To Handle The Small Impedance Angle In The Zero Sequence Impedance Test Results?
How To Handle The Small Impedance Angle In The Zero Sequence Impedance Test Results?
Q: How to handle the small impedance angle in the zero sequence impedance test results? Answer: The small impedance angle of zero sequence impedance is mainly due to the large resistance part. The following aspects can be checked: 1. Whether the grounding is good should be connected to the grounding grid inside the substation, and tower grounding devices or ···
How To Deal With Abnormal Output Voltage Of One Phase Of The Instrument?
How To Deal With Abnormal Output Voltage Of One Phase Of The Instrument?
Q: How to deal with abnormal output voltage of one phase of the instrument? Answer: 1. If the abnormal phase has a normal output current and a significantly low output voltage, it is possible that the voltage line is loose or disconnected, and the voltage line needs to be replaced before testing. If the voltage and current are both 0, it is possible that bot···
No data found!